Testing to Validate Asset Integrity Based on a Reference Code or Standard
Ultrasonic Testing (UT) uses high frequency ultrasonic waves to detect surface breaking and internal imperfections, measure material thickness and determine acceptance or rejection of a test object based on a reference code or standard. UT is completely nondestructive. The test piece does not have to be cut, sectioned, or exposed to damaging chemicals. Access to only one side is required.
A wide variety of cracks, voids, disbonds, inclusions, and similar problems that affect structural integrity can all be located and measured with UT methods. Test results are highly repeatable and reliable. The minimum detectable flaw size in a given application will depend on the type of material being tested and the type of flaw under consideration.
Ultrasonic Thickness Testing (UTT)
Our UTT measures remaining wall thickness on piping, pressure vessels, storage tanks and other materials, and can be used to scan bolts, shafts and raw materials for imperfections. A straight beam is directed at the test piece and, utilizing the round trip time for the ultra-sonic energy, the distance to the flaw is displayed in thousandths of an inch. On UT units with A-scan, the display will show multiple flaws at different depths.
Shearwave Ultrasonics (UT-S)
Our UT-S or A-scan testing transmits an ultrasonic wave at a predetermined angle into the test material. Surfaces normal to the beam path and corner traps reflect the wave energy back to the transducer. The display shows the distance the wave traveled to the imperfection and the relative strength of the energy.
Our B-scan is useful for corrosion analysis or locating laminations and inclusions in new rolled materials. Real-time imaging displays a profile of the test material along the scan path. Images can be stored for later review.
Our C-scan can be used to determine corrosion rates and code calculations. The inspection is done in an immersion tank or with a tank crawler, and data is displayed on a plane view utilizing a color system to indicate various material thicknesses.
Internal Rotating Inspection System (IRIS)
Our IRIS inspection detects defects and measures wall loss of both ferrous and nonferrous tubing. It provides information about the geometry of the defect while accurately measuring local defects and wall loss on both the inside and the outside of a tube. Defects under support plates are easily detected and quantified as well. Computerized reporting and tube sheet mapping are available.
Time of Flight Diffraction (TOFD)
Ideal for inspecting and sizing defects in welds, our TOFD uses two angled probes (one on each side of the weld) to transmit sound waves into the test material at angles specific to its thickness. Discontinuities are shown as breaks in the waves or as additional waves between mode lines. TOFD is normally utilized in conjunction with Phased Array UT.
Guided Wave Testing
Our advanced Guided Wave inspection services enable you to locate pipe defects above and below ground without disruption of service.
Learn More About Our Ultrasonic Testing (UT) Solutions
- Additional Capabilities
- Provide instant and accurate results
- Detect surface breaking and internal imperfections
- Measure material thickness
- Determine imperfections throughout the entire material thickness, and may be used with access to only one surface
- Determine acceptance or rejection of a test object based on a reference code or standard
- Fully-Certified Techs
TEAM’s tank inspection technicians are put through a rigorous, method specific, multi-level certification and training process resulting in the industry’s most knowledgeable and experienced team.
- Integrated Solutions
TEAM responds to our clients’ needs for increased asset management efficiency and reliability by providing higher value solutions with integrated services, covering projects from inception to completion. This allows for time and cost saving opportunities to be identified from reduced man hours and increased time on tools throughout the project.
- Digital Solutions
Our digital platform turns slow paper-driven processes into streamlined, fully-automated and fully transparent operations. This results in less re-work, more time-on-tools and less manual data entry for improved efficiencies.
- Core Values
Key Principles that Anchor Every Aspect of TEAM
TEAM's Core Values anchor every aspect of our business in a set of commonly-held beliefs and commitments. They represent what our company stands for, what values our employees embody, and what our services and products contribute to the market.